SlaughterPro | HUATAOSearch

Horizontal Carcass Hair Trimming Automatic Conveyor Machinery | HT-P211

Horizontal Carcass Hair Trimming Automatic Conveyor Machinery. Compare load range, dimensions and process interfaces; share your requirements for configuration review.

Horizontal Carcass Hair Trimming Automatic Conveyor Machinery — source product-family photograph; confirm the quoted configuration

Specification notes

ModelHT-P211
Rated voltage / phase / frequency380v / 3p / 50hz
Power1.5Kw
Out size5000*1550*500(L*W*H)
Component and material1) 38*38*2mm stainless square steel support 2) High-quality carbon steel sprockets, plate chain, drive shaft 3) 60*30*2mm stainless square steel convey plate 4) Driving &tension device
Data statusSource reference R1; configuration requires written confirmation

Use and process role

This Horizontal Carcass Hair Trimming Automatic Conveyor Machinery is specified for one practical job: a carcass-finishing station that removes remaining hair or surface residue after primary dehairing. A reliable installation begins with correct interface dimensions and a realistic duty cycle. The HT listing supplies reference data for the offered arrangement; those figures are reproduced below for comparison. For export quotations, confirm voltage, materials, guarding, spare parts and documentation before the purchase order is released.

Structure and working principle

The carcass passes rotating polishing elements, trimming positions or a controlled flame zone. Exposure is limited to the surface treatment needed before final washing and clean-line entry. The upstream machine must not feed faster than the receiving station can clear.

Source-listed construction and features

More uniform carcass finish

Adjustment for carcass size and line speed

Contained residue or exhaust

Guards around moving or hot parts

Easy access for cleaning

Integration with the overhead rail

Applications and integration

The usual application is pig slaughter lines between primary dehairing and final carcass washing. It can be specified for a new line or adapted to a retrofit, provided that the existing supports, working heights, utilities and control signals are measured on site. Plants handling several pig sizes should state the full range rather than quoting only an average.

Selection conditions and project fit

Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.

Evidence, configuration and document status

The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.

Source and version

Reference compilation R1, 2026-11-16. Supplied document: 2. 烫脱毛,剥皮,掏脏设备.doc; section 2.22. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.

The supplied documents reference one or more identifiers on other equipment pages. A repeated identifier is not proof that specifications, duties or revisions are identical. Review the linked source configurations and request a model-specific drawing before treating them as equivalent.

Installation and process interfaces

Provide the load and product range, travel direction, rail/belt section or mating geometry, working heights, supports and maintenance clearances. Similar appearance is not proof of fit.

Utilities, control and feedback requirements

For powered equipment, confirm the matching drive, supply, control and line signals. For passive components, confirm mechanical interfaces and any requirements of the receiving equipment; no powered or feedback capability should be assumed.

Maintenance and part identification

Request the configuration-specific manual and part references for rollers, chains, hooks, bearings, guides and drive elements where applicable. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Source-unit confirmation required

The supplied reference does not explicitly state a unit for these fields: Out size. The original entries are retained rather than assigning an assumed unit. Confirm the units, matching configuration and operating conditions before comparing these figures or approving a quotation.

Compare configurations for your project

For Horizontal Carcass Hair Trimming Automatic Conveyor Machinery | HT-P211, keep the complete identifier HT-P211 attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.

Start with this page's listed reference fields: Rated voltage / phase / frequency: 380v / 3p / 50hz; Power: 1.5Kw; Out size: 5000*1550*500(L*W*H); Component and material: 1) 38*38*2mm stainless square steel support 2) High-quality carbon steel sprockets, plate chain, drive shaft 3) 60*30*2mm stainless square steel convey plate 4) Driving &tension device. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.

Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.

Purchasing review and enquiry preparation

Start with Horizontal Carcass Hair Trimming Automatic Conveyor Machinery | HT-P211 and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.

Use the linked pig processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.

Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-P211 and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.

Source reference configuration 1
ParameterReference Value / Buyer Check
ModeLHT-P211
ApplicationWhich used to collect dehaired pig carcass for hair trimming,
Rated voltage / phase / frequency380v / 3p / 50hz
Power1.5Kw
Chain pitch100mm
Out size5000*1550*500(L*W*H)
Component and material1) 38*38*2mm stainless square steel support 2) High-quality carbon steel sprockets, plate chain, drive shaft 3) 60*30*2mm stainless square steel convey plate 4) Driving &tension device
Quotation controlSpecify line speed, carcass range, upstream dehairing result, required finish, exhaust or gas supply, fire controls and downstream washer position.

Buyer FAQ

What information is needed to quote the Horizontal Carcass Hair Trimming Automatic Conveyor Machinery?

Specify line speed, carcass range, upstream dehairing result, required finish, exhaust or gas supply, fire controls and downstream washer position.

Which spare parts should be ordered with the machine?

Start with the normal wear and hygiene parts for this duty: bearings, seals, sensors, chains or belts, nozzles, blades, scrapers, pneumatic parts and electrical protection devices as applicable. The supplier should issue a model-specific list.

Are the published technical figures final?

No. The table records reference information from the citedHTpage. Capacity, power, dimensions, material grade and utilities must be confirmed on the quotation and approved drawing.

How should the equipment be accepted after installation?

Use a documented site-acceptance test covering alignment, guards, emergency stops, interlocks, dry running, representative load, cleaning access, leakage or drainage, operator training and delivery of manuals and spares.

What information is needed to select this equipment?

Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.

Are these specifications an approved supply commitment?

No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.

Related configurations and guidance

Related source configuration: Pig Carcass Receiving and Transfer Table Pig processing equipment categories Pig processing process application Check complete model identifiers and suffixes

Reference specification and document status

Download HT-P211 reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Pig processing workflowExplore pig processing by process task, source equipment and project conditions.

Capabilities

Pig processing line planningExplore pig processing by process task, source equipment and project conditions.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-P211

Start with what you know. You can send drawings or photographs by email.

Continue your technical review

Pig processing processCompare published equipmentPrepare quotation informationSupplier verification checklistIdentify related replacement parts