SlaughterPro | HUATAOSearch

Cattle Hind Legs Separation Device for Beef Slaughterhouse | HT-C232

Cattle Hind Legs Separation Device. Compare load range, dimensions and process interfaces; share your requirements for configuration review.

Cattle Hind Legs Separation Device for Beef Slaughterhouse — source product-family photograph; confirm the quoted configuration

Specification notes

ModelHT-C232
Drive SystemPneumatic
Main MaterialStainless Steel / Hot Galvanized Steel
Data statusSource reference R1; configuration requires written confirmation

Use and process role

Cattle Hind Legs Separation Device for Efficient Beef Carcass Processing

The cattle hind legs separation device is specially designed for beef slaughterhouses and cattle abattoirs to separate and fix the rear legs of cattle carcasses during the dressing and carcass splitting process.

After slaughtering and skin removal, the cattle carcass is transported by an overhead rail conveyor system. During carcass splitting, inspection, trimming, and further processing, keeping the hind legs at a fixed distance is important to maintain carcass stability and improve operator safety.

This pneumatic leg separation system automatically spreads the two hind legs and locks them in position, preventing unwanted movement during carcass processing.

The equipment is mainly composed of stainless steel or hot galvanized connectors, rail sliders, pneumatic leg fixing mechanisms, and a pneumatic control system. It can be installed directly on cattle carcass conveyor rails and works continuously with the slaughterhouse workflow.

Compared with manual leg positioning methods, the cattle hind legs separator improves processing consistency, reduces labor requirements, and creates a safer working environment for operators.

The device is commonly used together with:

Cattle carcass splitting saw

Overhead carcass conveyor

Carcass inspection platform

Carcass processing elevator

Structure and working principle

The cattle hind legs separation device operates through a pneumatic control system installed on the overhead carcass rail.

When the cattle carcass enters the working position, the pneumatic cylinder activates the leg separation mechanism. The two rear legs are pushed outward to a preset distance and fixed securely.

The sliding mechanism follows the movement of the carcass conveyor, allowing continuous operation without removing the carcass from the rail.

After the splitting or inspection process is completed, the pneumatic system releases the fixation and allows the carcass to continue moving to the next processing stage.

The pneumatic drive provides fast response, stable positioning, and reliable operation in continuous beef processing environments.

Source-listed construction and features

1. Pneumatic Leg Separation System

The equipment uses compressed air as the driving power.

Applications and integration

The cattle hind legs separation device is mainly applied in:

Beef slaughterhouses

Cattle abattoirs

Meat processing factories

Beef export processing plants

Typical processing position:

Cattle Slaughter

↓

Bleeding

Hide Removal

Hind Legs Separation

Carcass Splitting

Inspection & Trimming

The equipment is especially suitable for medium and large-scale beef processing facilities where stable carcass positioning is required.

Selection conditions and project fit

State product or animal range, required duty and throughput, available space, utilities, connection dimensions and delivery scope. Confirm the configuration and acceptance criteria in writing.

Evidence, configuration and document status

The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.

Source and version

Reference compilation R1, 2026-11-16. Supplied document: 1. 牛致晕宰杀放血设备.doc; section 1.6. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.

Installation and process interfaces

Provide the load and product range, travel direction, rail/belt section or mating geometry, working heights, supports and maintenance clearances. Similar appearance is not proof of fit.

Utilities, control and feedback requirements

For powered equipment, confirm the matching drive, supply, control and line signals. For passive components, confirm mechanical interfaces and any requirements of the receiving equipment; no powered or feedback capability should be assumed.

Maintenance and part identification

Request the configuration-specific manual and part references for rollers, chains, hooks, bearings, guides and drive elements where applicable. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Compare configurations for your project

For Cattle Hind Legs Separation Device for Beef Slaughterhouse | HT-C232, keep the complete identifier HT-C232 attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.

Start with this page's listed reference fields: Drive System: Pneumatic; Main Material: Stainless Steel / Hot Galvanized Steel. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.

Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.

Purchasing review and enquiry preparation

Start with Cattle Hind Legs Separation Device for Beef Slaughterhouse | HT-C232 and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.

Use the linked cattle & beef processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.

Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-C232 and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.

Source reference configuration 1
ItemSpecification
Product NameCattle Hind Legs Separation Device
ModelHT-C232
ApplicationBeef carcass hind leg separation
Drive SystemPneumatic
Leg Separation Distance800 mm
Air ConsumptionApprox. 92 L/time
Control MethodPneumatic control system
Installation TypeOverhead carcass rail mounting
Main MaterialStainless Steel / Hot Galvanized Steel
Rail ComponentStainless Steel Track and Slider
Fixing SystemPneumatic Leg Clamp
Suitable AnimalCattle / Beef Carcass

Buyer FAQ

What is the purpose of a cattle hind legs separation device?

It is used to spread and fix cattle hind legs during carcass splitting and inspection processes.

How does the equipment move with the carcass?

The device is installed on the overhead rail system and follows the carcass conveyor movement.

What is the standard leg separation distance?

The standard separation distance is approximately 800mm.

What power source does the equipment use?

The system uses compressed air through a pneumatic control system.

What information is needed to select this equipment?

State product or animal range, required duty and throughput, available space, utilities, connection dimensions and delivery scope. Confirm the configuration and acceptance criteria in writing.

Are these specifications an approved supply commitment?

No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.

Related configurations and guidance

Cattle & beef processing equipment categories Cattle & beef processing process application Check complete model identifiers and suffixes

Reference specification and document status

Download HT-C232 reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Cattle & beef processing workflowExplore cattle & beef processing by process task, source equipment and project conditions.

Capabilities

Cattle & beef processing line planningExplore cattle & beef processing by process task, source equipment and project conditions.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-C232

Start with what you know. You can send drawings or photographs by email.

Continue your technical review