SlaughterPro | HUATAOSearch

Slope Type Pneumatic Sheep Skin Puller | HT-C207-I

Slope Type Pneumatic Sheep Skin Puller. Compare input range, required output and working interfaces; share your requirements for configuration review.

Slope Type Pneumatic Sheep Skin Puller — source product-family photograph; confirm the quoted configuration

Specification notes

ModelHT-C207-I
Installed power1.1 kW
Maximum stated capacity300 sheep/hour
Overall dimensions300 × 280 × 4,180 mm
Product-contact / roller materialStainless steel
Data statusSource reference R1; configuration requires written confirmation

Use and process role

The Slope Type Pneumatic Sheep Skin Puller is built for the dehiding station of a sheep or goat dressing line. It replaces the hardest part of manual pulling with a guided, powered movHTnt while leaving the operator in control of hide attachment and carcass presentation. The sloped arrangHTnt helps the pull follow the carcass rather than dragging the hide across the floor or into adjacent work areas.

Its reference construction combines a galvanized or stainless main column, a stainless-steel winding roller and a large pneumatic cylinder. The roller is motor driven, while compressed air supplies the controlled linear action. This mixed drive arrangHTnt is practical for plants that want a repeatable pull without committing to a full hydraulic system. Surfaces and guards should be specified to suit the buyer's sanitation regime, rail height and available floor space.

Structure and working principle

After the forelegs and an initial section of hide have been opened manually, the operator secures the loosened hide to the pulling roller. The pneumatic cylinder positions the pulling assembly and the geared drive rotates the roller at a controlled speed. As the hide winds onto the roller, it separates from the carcass along the inclined pulling path. The operator monitors tension and stops the cycle if trimming is needed. At the end of the pull, the hide is released to the collection or hide-conveying system and the roller is readied for the next carcass.

Source-listed construction and features

Inclined pulling path suited to suspended sheep and goat carcasses

Motor-driven stainless winding roller for a steady, repeatable pull

Pneumatic positioning based on a 0.6 MPa plant air supply

Reference capacity of up to 300 sheep per hour when correctly integrated

Choice of galvanized or stainless main column for different project budgets

Compact vertical footprint for installation beside an overhead dressing rail

Selection conditions and project fit

State incoming product size and temperature, target cut or separation, rate, output specification, interfaces, blade or tool arrangement and guarding requirements. Agree a representative-product trial and the acceptance criteria.

Evidence, configuration and document status

The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.

Source and version

Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.1. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.

Installation and process interfaces

Provide product size and condition, target cut or separation, feed/discharge direction, support height and space for tool replacement and maintenance. Confirm the proposed guards, operator access and connection to the receiving station.

Utilities, control and feedback requirements

Check the model-specific drive and electrical or fluid-power supply. Agree start/stop, upstream/downstream interlocks and feedback requirements where relevant. Do not infer a control protocol or tool capability from a family photograph.

Maintenance and part identification

Request the configuration-specific manual and part references for matched blades or tools, drive components, seals and position sensors where fitted. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Compare configurations for your project

For Slope Type Pneumatic Sheep Skin Puller | HT-C207-I, keep the complete identifier HT-C207-I attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.

Start with this page's listed reference fields: Installed power: 1.1 kW; Maximum stated capacity: 300 sheep/hour; Overall dimensions: 300 × 280 × 4,180 mm; Product-contact / roller material: Stainless steel. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.

Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.

Purchasing review and enquiry preparation

Start with Slope Type Pneumatic Sheep Skin Puller | HT-C207-I and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.

Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.

Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-C207-I and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.

Source reference configuration 1
PARAMETERREFERENCE SPECIFICATION
Reference modelHT-C207-I
Operating typeAutomatic pneumatic skin puller
Electrical supply380 V / 50 Hz / 3 phase
Installed power1.1 kW
Roller speed41 rpm
Working air pressure0.6 MPa
Maximum stated capacity300 sheep/hour
Overall dimensions300 × 280 × 4,180 mm
Main cylinderAluminium cylinder, Ø125 × 1,600 mm
Product-contact / roller materialStainless steel
Main column optionsGalvanized steel or stainless steel

Buyer FAQ

What utilities are required?

The reference unit requires 380 V, 50 Hz, three-phase power and a clean, regulated 0.6 MPa compressed-air supply.

Does the machine eliminate manual knife work?

No. Operators still open and prepare the hide, attach it correctly and trim areas that do not release cleanly.

Which items should be kept as critical spares?

Typical spares include cylinder seal kits, pneumatic valves, hoses, roller attachment parts, bearings, gearbox seals and electrical controls.

What information is needed to select this equipment?

State incoming product size and temperature, target cut or separation, rate, output specification, interfaces, blade or tool arrangement and guarding requirements. Agree a representative-product trial and the acceptance criteria.

Are these specifications an approved supply commitment?

No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.

Related configurations and guidance

Sheep & goat processing equipment categories Sheep & goat processing process application Check complete model identifiers and suffixes

Reference specification and document status

Download HT-C207-I reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Sheep & goat processing workflowExplore sheep & goat processing by process task, source equipment and project conditions.

Capabilities

Sheep & goat processing line planningExplore sheep & goat processing by process task, source equipment and project conditions.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-C207-I

Start with what you know. You can send drawings or photographs by email.

Continue your technical review