Automatic Sheep Carcass Washing Machine | HT-S218-II
Automatic Sheep Carcass Washing Machine. Compare product range, residence time and utility conditions; share your requirements for configuration review.

Supplied product-directory reference image: equipment family or process context. It is not proof of an exact model, HUATAO installation or certification. Confirm the proposed configuration photograph and drawing before ordering.
Specification notes
| Model | HT-S218-II |
|---|---|
| Installed power | 2.2 kW |
| Maximum stated capacity | 400 head/hour |
| Data status | Source reference R1; configuration requires written confirmation |
Use and process role
Final rinsing needs a defined station. If every operator uses a hose differently, coverage and water consumption soon drift. This washer puts the carcass inside a cabinet, senses its arrival and applies the same timed spray on each pass. It is meant to lift away loose material before weighing or chilling. Good dressing practice still comes first; a rinse cannot turn a poorly handled carcass into an acceptable one.
For model HT-S218-II, the source lists a 2.2 kW pump package and stainless water lines inside a 304 stainless housing. The nominal flow is 2 m³/h, while the exposure time can be adjusted at the control. HT quotes an upper line rate of 400 animals per hour. Before accepting that figure, the buyer should check nozzle positions, available water pressure, rail speed and drain capacity with its own carcass range. Too much pressure or a badly aimed jet can spread droplets rather than improve the finish.
Structure and working principle
The trolley brings a dressed carcass through the cabinet entrance. As it crosses the sensing point, the control begins the programmed wash window. Water reaches the surface from the arranged nozzle banks, and the cabinet walls keep most of the splash over the drain. Spraying ends at the timer setting, then the rail carries the carcass into a short drip zone before the scale or chiller. At start-up, the crew checks the pattern with water only and clears any nozzle that throws an uneven fan. Strainers, cabinet corners and the drain are cleaned at the end of the run.
Source-listed construction and features
Spray begins only when the incoming carcass reaches the sensor
Wash duration can be adjusted at the control
304 stainless cabinet around the wet station
Reference water flow of 2 m³ per hour
Listed line-rate ceiling of 400 head per hour
Selection conditions and project fit
Define product size, residence time, line speed, water quality, temperature, pressure, flow and drainage. Specify the hygiene process and acceptance method; a machine name does not establish a validated hygiene result.
Evidence, configuration and document status
The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.
Source and version
Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.10. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.
Installation and process interfaces
State incoming product condition, process residence time, line speed, working height, water connections, drain location and access for cleaning or component removal. Check the full installation envelope, not only catalogue dimensions.
Utilities, control and feedback requirements
Use only the power, water, heating or cooling values given for the matching source configuration. Confirm operating pressure/flow or temperature, control method and line signals. A reference machine does not establish a validated hygiene or cooling result.
Maintenance and part identification
Request the configuration-specific manual and part references for nozzles, seals, pumps, sensors, conveying elements and any heating/cooling components fitted. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.
Configuration-specific document checklist
Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.
Compare configurations for your project
For Automatic Sheep Carcass Washing Machine | HT-S218-II, keep the complete identifier HT-S218-II attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.
Start with this page's listed reference fields: Installed power: 2.2 kW; Maximum stated capacity: 400 head/hour. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.
Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.
Purchasing review and enquiry preparation
Start with Automatic Sheep Carcass Washing Machine | HT-S218-II and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.
Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.
Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-S218-II and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.
| PARAMETER | REFERENCE SPECIFICATION |
|---|---|
| Reference model | HT-S218-II |
| Electrical supply | 380 V / 3 phase / 50 Hz |
| Installed power | 2.2 kW |
| Rated water flow | 2 m³/hour |
| Maximum stated capacity | 400 head/hour |
| Activation | Automatic induction sensor |
| Wash time | Adjustable |
| Enclosure | 304 stainless steel |
| Pump and piping | High-pressure pump with stainless piping |
| Nozzle pressure / water quality | Not stated; confirm for the site |
Buyer FAQ
Does washing make a contaminated carcass safe?
No. Visible contamination must be handled under the plant's approved procedure. Washing cannot correct poor dressing practice by itself.
What pressure does the pump deliver?
The source states a high-pressure pump but gives no pressure. Ask for the pump curve, nozzle schedule and operating pressure.
How often should nozzles be checked?
Check spray coverage before production and whenever the pattern changes. Water hardness and solids determine cleaning frequency.
Can chemical sanitizer be dosed into the washer?
Only if local rules allow it and the pump, seals and controls are designed for that chemical. The listed configuration does not confirm a dosing system.
What information is needed to select this equipment?
Define product size, residence time, line speed, water quality, temperature, pressure, flow and drainage. Specify the hygiene process and acceptance method; a machine name does not establish a validated hygiene result.
Are these specifications an approved supply commitment?
No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.
Related configurations and guidance
Reference specification and document status
Download HT-S218-II reference specification and verification checklist
This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.