SlaughterPro | HUATAOSearch

Vertical Electric Sheep Skin Puller | HT-C207-III

Vertical Electric Sheep Skin Puller. Compare input range, required output and working interfaces; share your requirements for configuration review.

Vertical Electric Sheep Skin Puller — source product-family photograph; confirm the quoted configuration

Specification notes

ModelHT-C207-III
Installed power1.5 kW
Maximum stated capacity100 sheep/hour
Overall dimensions / rail interfaceNot stated; project-specific
Data statusSource reference R1; configuration requires written confirmation

Use and process role

The Vertical Electric Sheep Skin Puller uses a motor-driven stainless roller to remove the main hide from a suspended sheep or goat carcass. Its upright format occupies little floor width and suits lower-capacity lines that want a powered pull without a separate hydraulic power pack. Variable roller speed allows the operator to slow the movHTnt for difficult hides and increase it when preparation is consistent.

The reference unit is rated at 1.5 kW with a pulling-speed range of 1.6–16 m/min and a stated maximum of 100 sheep per hour. Galvanized or stainless framing is offered. The source also lists a 6 MPa working pressure even though the product is described as electric; the circuit associated with that pressure is not identified. This value must be clarified rather than copied into a final purchase specification as a confirmed utility.

Structure and working principle

Operators open the hide around the legs and free enough material for secure attachment to the pulling roller or chain. The electric drive rotates the roller and draws the hide downward or along the configured vertical path while the carcass stays on the rail. Speed is adjusted to suit carcass condition and operator trimming. Once the hide has separated, it is released to a collection point and the roller reverses or resets. Guards and an HTrgency stop should remain within easy reach throughout the cycle.

Source-listed construction and features

Vertical layout for a narrow dehiding station

Variable pulling speed from 1.6 to 16 m/min

Stainless pulling roller

Galvanized or stainless main-frame options

Maximum stated output of 100 sheep per hour

Selection conditions and project fit

State incoming product size and temperature, target cut or separation, rate, output specification, interfaces, blade or tool arrangement and guarding requirements. Agree a representative-product trial and the acceptance criteria.

Evidence, configuration and document status

The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.

Source and version

Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.13. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.

Installation and process interfaces

Provide product size and condition, target cut or separation, feed/discharge direction, support height and space for tool replacement and maintenance. Confirm the proposed guards, operator access and connection to the receiving station.

Utilities, control and feedback requirements

Check the model-specific drive and electrical or fluid-power supply. Agree start/stop, upstream/downstream interlocks and feedback requirements where relevant. Do not infer a control protocol or tool capability from a family photograph.

Maintenance and part identification

Request the configuration-specific manual and part references for matched blades or tools, drive components, seals and position sensors where fitted. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Compare configurations for your project

For Vertical Electric Sheep Skin Puller | HT-C207-III, keep the complete identifier HT-C207-III attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.

Start with this page's listed reference fields: Installed power: 1.5 kW; Maximum stated capacity: 100 sheep/hour; Overall dimensions / rail interface: Not stated; project-specific. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.

Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.

Purchasing review and enquiry preparation

Start with Vertical Electric Sheep Skin Puller | HT-C207-III and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.

Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.

Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-C207-III and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.

Source reference configuration 1
PARAMETERREFERENCE SPECIFICATION
Reference modelHT-C207-III
Operating typeElectric skin puller
Electrical supply380 V / 50 Hz / 3 phase
Installed power1.5 kW
Pulling speed1.6–16 m/min
Maximum stated capacity100 sheep/hour
Main frameGalvanized steel or stainless steel
Pulling rollerStainless steel
Listed working pressure6 MPa — circuit not identified; supplier clarification required
Overall dimensions / rail interfaceNot stated; project-specific

Buyer FAQ

Why does an electric puller list 6 MPa working pressure?

The source does not explain it. It may refer to an omitted auxiliary circuit or be a data error. Obtain a utility diagram before ordering.

Can the speed be adjusted during production?

The listing provides a 1.6–16 m/min range. Confirm the control type and whether adjustment is available from the operator station.

Is this model suitable for 200 sheep per hour?

No. Its stated maximum is 100 sheep per hour. Higher line rates require another configuration or parallel stations.

Does it remove the hide without pre-skinning?

No. The legs and initial hide area must be opened and prepared manually.

What information should be sent with an enquiry?

Provide carcass weight range, rail height and profile, target rate, pulling direction, available utilities, preferred frame material and the planned hide discharge.

What information is needed to select this equipment?

State incoming product size and temperature, target cut or separation, rate, output specification, interfaces, blade or tool arrangement and guarding requirements. Agree a representative-product trial and the acceptance criteria.

Are these specifications an approved supply commitment?

No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.

Related configurations and guidance

Sheep & goat processing equipment categories Sheep & goat processing process application Check complete model identifiers and suffixes

Reference specification and document status

Download HT-C207-III reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Sheep & goat processing workflowExplore sheep & goat processing by process task, source equipment and project conditions.

Capabilities

Sheep & goat processing line planningExplore sheep & goat processing by process task, source equipment and project conditions.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-C207-III

Start with what you know. You can send drawings or photographs by email.

Continue your technical review