White and Red Viscera Sliding Chute | HT-S216-I
White and Red Viscera Sliding Chute. Compare load range, dimensions and process interfaces; share your requirements for configuration review.

Specification notes
| Model | HT-S216-I |
|---|---|
| Nominal dimensions | 1,300 × 900 × 60 mm |
| Material | 304 stainless steel throughout |
| Drive power | Not required |
| Data status | Source reference R1; configuration requires written confirmation |
Use and process role
The White and Red Viscera Sliding Chute provides a simple, washable route for moving organs away from the evisceration point. In a well-planned sheep line, it prevents edible and non-edible material from being carried by hand across a platform and keeps the transfer path defined. The chute can serve red viscera, white viscera or two segregated duties when the surrounding layout provides the required separation.
The reference unit is made entirely from 304 stainless steel with a 2 mm sheet thickness. It has no motor, gearbox or chain, so maintenance is limited mainly to cleaning, inspection and checking the supports. Correct installation is more important than complexity: the inlet height, slope, edge treatment and receiving container must allow viscera to move without splashing, backing up or contacting the floor.
Structure and working principle
Viscera are placed into the upper end of the chute after removal from the carcass. Gravity carries the material down the smooth stainless surface to an inspection tray, conveyor, collection bin or processing table. The chute angle supplies the movHTnt; no powered drive is required. During sanitation, the open profile allows direct rinsing and visual inspection. For separate red and white offal streams, the plant should use independent chutes or a positively separated arrangHTnt rather than relying on timing alone.
Source-listed construction and features
Full 304 stainless-steel construction in the reference configuration
2 mm sheet thickness for a practical balance of rigidity and cleanability
Open, smooth transfer surface with no concealed conveyor return path
Gravity operation with no motor, reducer or electrical cabinet
Compact footprint for mounting beside an evisceration platform
Can discharge to an offal conveyor, inspection table or dedicated receiving bin
Selection conditions and project fit
Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.
Evidence, configuration and document status
The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.
Source and version
Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.2. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.
Installation and process interfaces
Provide the load and product range, travel direction, rail/belt section or mating geometry, working heights, supports and maintenance clearances. Similar appearance is not proof of fit.
Utilities, control and feedback requirements
For powered equipment, confirm the matching drive, supply, control and line signals. For passive components, confirm mechanical interfaces and any requirements of the receiving equipment; no powered or feedback capability should be assumed.
Maintenance and part identification
Request the configuration-specific manual and part references for rollers, chains, hooks, bearings, guides and drive elements where applicable. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.
Configuration-specific document checklist
Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.
Compare configurations for your project
For White and Red Viscera Sliding Chute | HT-S216-I, keep the complete identifier HT-S216-I attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.
Start with this page's listed reference fields: Nominal dimensions: 1,300 × 900 × 60 mm; Material: 304 stainless steel throughout; Drive power: Not required. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.
Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.
Purchasing review and enquiry preparation
Start with White and Red Viscera Sliding Chute | HT-S216-I and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.
Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.
Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-S216-I and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.
| PARAMETER | REFERENCE SPECIFICATION |
|---|---|
| Reference model | HT-S216-I |
| Nominal dimensions | 1,300 × 900 × 60 mm |
| Sheet thickness | 2 mm |
| Material | 304 stainless steel throughout |
| Transfer method | Gravity slide |
| Drive power | Not required |
| Intended media | White and/or red viscera, with process segregation |
| Mounting | Project-specific supports and slope |
| Surface finish | Confirm with supplier for the hygiene specification |
Buyer FAQ
Can one chute be used for both red and white viscera?
It can be assigned to either duty, but simultaneous streams should be physically separated to protect hygiene and inspection traceability.
What slope is required?
The source does not state an angle. The equipment supplier should set the slope after considering product condition, transfer distance and receiving height.
Is a cover recommended?
cover or splash guard may be useful where overhead contamination is possible, provided it can be opened or removed for complete cleaning.
What spare parts are needed?
There are few wear parts. Plants normally keep replacHTnt mounting hardware, edge guards and any removable spray fittings used in their own installation.
What information is needed to select this equipment?
Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.
Are these specifications an approved supply commitment?
No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.
Related configurations and guidance
Reference specification and document status
Download HT-S216-I reference specification and verification checklist
This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.