SlaughterPro | HUATAOSearch

Hanging Type Sheep Offal Synchronous Inspection Conveyor | HT-S215-II

Hanging Type Sheep Offal Synchronous Inspection Conveyor. Compare load range, dimensions and process interfaces; share your requirements for configuration review.

Hanging Type Sheep Offal Synchronous Inspection Conveyor | HT-S215-II — supplied product-directory equipment/process illustration; exact model configuration must be confirmed

Supplied product-directory reference image: equipment family or process context. It is not proof of an exact model, HUATAO installation or certification. Confirm the proposed configuration photograph and drawing before ordering.

Specification notes

ModelHT-S215-II
Installed power1.5 kW
Maximum stated capacity300 head/hour
Track and chain material304 stainless steel
Data statusSource reference R1; configuration requires written confirmation

Use and process role

The Hanging Type Sheep Offal Synchronous Inspection Conveyor keeps red and white viscera moving in step with the corresponding carcass. Instead of sending trays along the floor, it carries the inspection points on an elevated stainless chain and track. This leaves more of the floor open and gives the veterinary team a defined sequence for viewing carcass, organs and disposition status.

The reference design uses 304 stainless steel for the track, chain, trays and hooks. White offal is presented in trays, while red offal is carried on hooks or dedicated supports. A sterilizing provision is included for the hook circuit. The unit should be engineered as part of the line rather than ordered in isolation, because pitch, elevation, inspection dwell time and conveyor speed must match the carcass rail.

Structure and working principle

As each carcass reaches evisceration, its viscera are placed on the corresponding numbered or sequenced tray and hook. The overhead conveyor advances at a fixed relationship to the carcass line, carrying both streams through the inspection zone. The 1,200 mm reference pitch provides one repeated station per carcass. After inspection, accepted offal is removed for further handling and rejected material is diverted according to plant procedure. Empty carriers pass through the cleaning and sterilizing section before returning to the loading point.

Source-listed construction and features

Suspended layout keeps the return circuit and carrier structure off the main floor

Synchronous presentation of carcass, white offal and red offal

304 stainless track, chain, trays and hooks in the stated configuration

Reference tray/hook pitch of 1,200 mm

Integrated hook-sterilizing provision

Designed for line capacities up to 300 head per hour

Selection conditions and project fit

Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.

Evidence, configuration and document status

The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.

Source and version

Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.3. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.

Installation and process interfaces

Provide the load and product range, travel direction, rail/belt section or mating geometry, working heights, supports and maintenance clearances. Similar appearance is not proof of fit.

Utilities, control and feedback requirements

For powered equipment, confirm the matching drive, supply, control and line signals. For passive components, confirm mechanical interfaces and any requirements of the receiving equipment; no powered or feedback capability should be assumed.

Maintenance and part identification

Request the configuration-specific manual and part references for rollers, chains, hooks, bearings, guides and drive elements where applicable. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Compare configurations for your project

For Hanging Type Sheep Offal Synchronous Inspection Conveyor | HT-S215-II, keep the complete identifier HT-S215-II attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.

Start with this page's listed reference fields: Installed power: 1.5 kW; Maximum stated capacity: 300 head/hour; Track and chain material: 304 stainless steel. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.

Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.

Purchasing review and enquiry preparation

Start with Hanging Type Sheep Offal Synchronous Inspection Conveyor | HT-S215-II and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.

Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.

Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-S215-II and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.

Source reference configuration 1
PARAMETERREFERENCE SPECIFICATION
Reference modelHT-S215-II
Electrical supply380 V / 3 phase / 50 Hz
Installed power1.5 kW
Maximum stated capacity300 head/hour
Carrier pitch1,200 mm
Track and chain material304 stainless steel
Trays and hooks304 stainless steel
Sanitation provisionHook sterilizer; confirm tray-wash scope
Mounting height and lengthProject-specific
Speed controlConfirm drive and line synchronization method

Buyer FAQ

How is the offal conveyor synchronized with the carcass rail?

The drive and control logic must be engineered around the carcass pitch and line speed. The source listing does not define the control architecture.

Are trays and hooks both included?

The reference listing describes 304 stainless trays and hooks. Confirm quantities, carrier style and spare carriers in the quotation.

Can the conveyor operate above 300 head per hour?

Three hundred head per hour is the stated maximum. A higher rate would require a revised pitch, speed and inspection-time study.

Does the sterilizer cover every food-contact surface?

The listing specifically mentions a hook sterilizer. Tray washing and return-line sanitation should be confirmed separately.

What should be checked during maintenance?

Inspect chain tension, sprockets, carrier attachments, guides, drive lubrication points, sensors and the sterilizer temperature or water supply.

What information is needed to select this equipment?

Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.

Are these specifications an approved supply commitment?

No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.

Related configurations and guidance

Sheep & goat processing equipment categories Sheep & goat processing process application Check complete model identifiers and suffixes

Reference specification and document status

Download HT-S215-II reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Sheep & goat processing workflowExplore sheep & goat processing by process task, source equipment and project conditions.

Capabilities

Sheep & goat processing line planningExplore sheep & goat processing by process task, source equipment and project conditions.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-S215-II

Start with what you know. You can send drawings or photographs by email.

Continue your technical review