SlaughterPro | HUATAOSearch

Sheep Skin Belt Conveyor | HT-S208

Sheep Skin Belt Conveyor. Compare load range, dimensions and process interfaces; share your requirements for configuration review.

Sheep Skin Belt Conveyor — source product-family photograph; confirm the quoted configuration

Specification notes

ModelHT-S208
Installed power0.55 kW — normalized from a malformed source value; confirm
Overall dimensions6,000 × 520 × 400 mm
Belt materialFood-grade nylon
Drive and driven shaftsStainless steel
Data statusSource reference R1; configuration requires written confirmation

Use and process role

A hide that drops beside the dressing rail quickly becomes a handling and sanitation problem. The Sheep Skin Belt Conveyor collects released sheep or goat skins at the puller and transports them to a grading table, curing area, by-product room or external container. The belt creates one planned route and reduces repeated lifting through the wet processing zone.

The listed configuration is six metres long with a 450 mm food-grade nylon belt. Stainless rectangular tube forms the supporting frame, while raised stainless guards help retain the load. Both drive and driven shafts are stainless steel. Because hides are irregular, wet and sometimes folded, the conveyor should be sized for the actual drop point and discharge height rather than selected on belt width alone.

Structure and working principle

The drive motor turns the head shaft and moves the endless belt along the conveyor bed. A released hide lands on the loading section and is carried toward the discharge point; side guards reduce the chance of it sliding off. The return strand travels beneath the carrying surface and passes around the tail shaft. Operators remove or divert skins at the outlet. During cleaning, the belt should be slackened or lifted where the design permits so that the underside, rollers, guards and return path can be reached.

Source-listed construction and features

450 mm food-grade nylon belt in the reference specification

Six-metre transfer length for linking the puller to a hide room or collection point

Stainless structural tubes and stainless drive shafts

100 mm stainless side guards to retain uneven loads

Low installed motor power for continuous material transfer

Layout can be arranged horizontal or with a project-specific incline

Selection conditions and project fit

Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.

Evidence, configuration and document status

The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.

Source and version

Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.4. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.

Installation and process interfaces

Provide the load and product range, travel direction, rail/belt section or mating geometry, working heights, supports and maintenance clearances. Similar appearance is not proof of fit.

Utilities, control and feedback requirements

For powered equipment, confirm the matching drive, supply, control and line signals. For passive components, confirm mechanical interfaces and any requirements of the receiving equipment; no powered or feedback capability should be assumed.

Maintenance and part identification

Request the configuration-specific manual and part references for rollers, chains, hooks, bearings, guides and drive elements where applicable. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Compare configurations for your project

For Sheep Skin Belt Conveyor | HT-S208, keep the complete identifier HT-S208 attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.

Start with this page's listed reference fields: Installed power: 0.55 kW — normalized from a malformed source value; confirm; Overall dimensions: 6,000 × 520 × 400 mm; Belt material: Food-grade nylon; Drive and driven shafts: Stainless steel. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.

Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.

Purchasing review and enquiry preparation

Start with Sheep Skin Belt Conveyor | HT-S208 and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.

Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.

Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-S208 and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.

Source reference configuration 1
PARAMETERREFERENCE SPECIFICATION
Reference modelHT-S208
Electrical supply380 V / 50 Hz / 3 phase
Installed power0.55 kW — normalized from a malformed source value; confirm
Overall dimensions6,000 × 520 × 400 mm
Belt width450 mm
Belt materialFood-grade nylon
Main frame tubesStainless 60 × 40 × 2 mm and 38 × 25 × 2 mm
Side guard100 mm stainless steel
Drive and driven shaftsStainless steel
Belt speedNot stated; confirm for the line layout

Buyer FAQ

Is the listed 0.55 kW motor value final?

The source text is malformed and appears to mean 0.55 kW. Treat it as a reference only and obtain a confirmed motor schedule.

How is the belt cleaned?

Use the plant's approved low-pressure pre-rinse and cleaning procedure, and make sure the return path and shaft areas are accessible. Final chemical limits depend on the belt material.

Which belt should be ordered as a spare?

Record the belt's exact width, endless length, thickness, splice type, surface pattern and food-contact declaration. Width alone is not enough.

Can one conveyor handle skins and edible offal?

That is not recommended without a documented segregation and sanitation plan. Separate conveyors make hygiene control clearer.

What information is needed to select this equipment?

Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.

Are these specifications an approved supply commitment?

No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.

Related configurations and guidance

Sheep & goat processing equipment categories Sheep & goat processing process application Check complete model identifiers and suffixes

Reference specification and document status

Download HT-S208 reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Sheep & goat processing workflowExplore sheep & goat processing by process task, source equipment and project conditions.

Capabilities

Sheep & goat processing line planningExplore sheep & goat processing by process task, source equipment and project conditions.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-S208

Start with what you know. You can send drawings or photographs by email.

Continue your technical review