SlaughterPro | HUATAOSearch

Sheep and Goat Hoof & Head Scalding Tank | HT-S310

Sheep and Goat Hoof & Head Scalding Tank. Compare product range, residence time and utility conditions; share your requirements for configuration review.

Sheep and Goat Hoof & Head Scalding Tank — source product-family photograph; confirm the quoted configuration

Specification notes

ModelHT-S310
Overall dimensions1,800 × 800 × 700 mm
Batch capacity / steam demandNot stated; confirm from load size and recovery time
Data statusSource reference R1; configuration requires written confirmation

Use and process role

The Sheep and Goat Hoof & Head Scalding Tank conditions heads and feet before mechanical dehairing or manual finishing. A controlled hot-water soak softens the hair follicles and loosens dirt without relying on an open boiling vessel. Stable temperature matters: water that is too cool lengthens the process, while excessive heat can damage the surface and make downstream handling less consistent.

The reference tank uses steam heating, a 2 mm stainless outer shell and 60 mm polyurethane insulation. A galvanized internal support carries the load, while a stainless steam pipe distributes heat. Temperature control is included. Basket, hoist, overflow arrangHTnt and agitation are not fully described in the source and should be selected around batch size, operator ergonomics and local pressure-vessel or steam regulations.

Structure and working principle

The tank is filled to its operating level and steam is admitted through the submerged stainless pipe. The temperature controller cycles the steam valve to maintain the set range. Hooves or heads are placed in a basket or otherwise retained below the water surface for a validated time. Heat transfers into the skin and loosens the hair. The batch is then drained or lifted and transferred promptly to the dehairing machine. Floating debris is removed, and the vessel is emptied and cleaned at the frequency set by the plant's hygiene plan.

Source-listed construction and features

Reference scalding range of 58–62°C

Steam-heated water bath with stainless distribution pipe

60 mm polyurethane insulation to reduce heat loss

2 mm stainless external shell for a washable working area

Automatic temperature-control provision

Sized for sheep/goat heads, hooves and similar small by-products

Selection conditions and project fit

Define product size, residence time, line speed, water quality, temperature, pressure, flow and drainage. Specify the hygiene process and acceptance method; a machine name does not establish a validated hygiene result.

Evidence, configuration and document status

The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.

Source and version

Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.5. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.

Installation and process interfaces

State incoming product condition, process residence time, line speed, working height, water connections, drain location and access for cleaning or component removal. Check the full installation envelope, not only catalogue dimensions.

Utilities, control and feedback requirements

Use only the power, water, heating or cooling values given for the matching source configuration. Confirm operating pressure/flow or temperature, control method and line signals. A reference machine does not establish a validated hygiene or cooling result.

Maintenance and part identification

Request the configuration-specific manual and part references for nozzles, seals, pumps, sensors, conveying elements and any heating/cooling components fitted. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Compare configurations for your project

For Sheep and Goat Hoof & Head Scalding Tank | HT-S310, keep the complete identifier HT-S310 attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.

Start with this page's listed reference fields: Overall dimensions: 1,800 × 800 × 700 mm; Batch capacity / steam demand: Not stated; confirm from load size and recovery time. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.

Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.

Purchasing review and enquiry preparation

Start with Sheep and Goat Hoof & Head Scalding Tank | HT-S310 and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.

Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.

Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-S310 and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.

Source reference configuration 1
PARAMETERREFERENCE SPECIFICATION
Reference modelHT-S310
Process temperature58–62°C
Heating methodSteam
Overall dimensions1,800 × 800 × 700 mm
Outer shell2 mm stainless steel
Insulation60 mm polyurethane
Internal supportGalvanized steel in the reference listing
Steam pipeStainless steel
Temperature controlIncluded; sensor and valve details to be confirmed
Batch capacity / steam demandNot stated; confirm from load size and recovery time

Buyer FAQ

Why is the temperature range 58–62°C?

It is the range stated for the reference unit and is commonly used to loosen hair. The plant must still validate the combination of temperature and time.

Is an electric-heated version available?

The listed model is steam heated. Electric or hot-water alternatives would require a different heating calculation and control package.

Does the tank include a basket or hoist?

These items are not clearly specified on the source page. Include them explicitly in the request for quotation if required.

How much steam does the tank consume?

Steam demand is not stated. It depends on fill volume, incoming water temperature, batch loading, insulation and required recovery time.

Can heads and hooves be processed together?

They can share equipment only if the plant's product flow and hygiene plan allow it. Separate batches normally simplify time control and downstream handling.

What information is needed to select this equipment?

Define product size, residence time, line speed, water quality, temperature, pressure, flow and drainage. Specify the hygiene process and acceptance method; a machine name does not establish a validated hygiene result.

Are these specifications an approved supply commitment?

No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.

Related configurations and guidance

Sheep & goat processing equipment categories Sheep & goat processing process application Check complete model identifiers and suffixes

Reference specification and document status

Download HT-S310 reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Sheep & goat processing workflowExplore sheep & goat processing by process task, source equipment and project conditions.

Capabilities

Sheep & goat processing line planningExplore sheep & goat processing by process task, source equipment and project conditions.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-S310

Start with what you know. You can send drawings or photographs by email.

Continue your technical review