Pneumatic Sheep Carcass Rail Unloading Device | HT-S209
Pneumatic Sheep Carcass Rail Unloading Device. Compare load range, dimensions and process interfaces; share your requirements for configuration review.

Supplied product-directory reference image: equipment family or process context. It is not proof of an exact model, HUATAO installation or certification. Confirm the proposed configuration photograph and drawing before ordering.
Specification notes
| Model | HT-S209 |
|---|---|
| Overall dimensions | 415 × 500 × 1,200 mm |
| Cylinder material | Aluminium |
| Data status | Source reference R1; configuration requires written confirmation |
Use and process role
The Pneumatic Sheep Carcass Rail Unloading Device provides a controlled way to remove a suspended load from the dressing rail. The reference application is transfer from the rail toward a scalding tank, although the same principle may be used at a collection table or other receiving point when the geometry is engineered accordingly. It avoids uncontrolled manual lifting or dropping at a rail break.
A compact galvanized or stainless frame supports the guide and pneumatic cylinder. The stated lifting capacity is 300 kg, which provides a wide margin for sheep and goat carcasses but must not be confused with cycle throughput. The receiving equipment, hook path and guarding are as important as the actuator; a correctly rated device can still be unsafe if the carcass has nowhere controlled to move after release.
Structure and working principle
A carcass trolley or hook reaches the unloading position and is stopped by the rail guide. When the operator or line sensor initiates the cycle, the pneumatic cylinder moves the unloading arm through its working stroke. The mechanism lifts, pushes or tips the trolley past the rail retaining point, allowing the carcass to transfer to the receiving tank or support. The cylinder then retracts and the guide resets. Interlocks should prevent a new carcass from entering until the receiving area is clear and the arm has returned.
Source-listed construction and features
Pneumatic operation for a short, controlled unloading stroke
Reference load rating of 300 kg
Compact 415 × 500 mm plan dimensions
Galvanized or stainless frame options
Dedicated guide and aluminium pneumatic cylinder
Can be interlocked with a rail stop or receiving-tank sequence
Selection conditions and project fit
Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.
Evidence, configuration and document status
The descriptions and tables below are source-listed reference information, not independently measured results. Confirm material grade, electrical supply, dimensions, duty, guards, controls and delivery scope in the approved quotation and drawing. No model-specific certificate or verified customer installation is established by this page. Request the document issuer, applicable model, scope and revision before relying on a compliance claim.
Source and version
Reference compilation R1, 2026-11-16. Supplied document: 2. 羊剥皮 内脏处理 称重 清洗设备.doc; section 2.7. Configuration rows retain source units. Where the source lists alternatives or several models, each row must be checked as a separate configuration; a capacity or dimension must not be transferred between models.
Installation and process interfaces
Provide the load and product range, travel direction, rail/belt section or mating geometry, working heights, supports and maintenance clearances. Similar appearance is not proof of fit.
Utilities, control and feedback requirements
For powered equipment, confirm the matching drive, supply, control and line signals. For passive components, confirm mechanical interfaces and any requirements of the receiving equipment; no powered or feedback capability should be assumed.
Maintenance and part identification
Request the configuration-specific manual and part references for rollers, chains, hooks, bearings, guides and drive elements where applicable. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.
Configuration-specific document checklist
Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.
Compare configurations for your project
For Pneumatic Sheep Carcass Rail Unloading Device | HT-S209, keep the complete identifier HT-S209 attached to its own source configuration. Compare process duty, incoming animal or product range, target output, utilities, installation envelope and upstream/downstream interfaces under the same project conditions. A higher catalogue rate alone does not establish a better fit.
Start with this page's listed reference fields: Overall dimensions: 415 × 500 × 1,200 mm; Cylinder material: Aluminium. Confirm units, conditions and revision against the quoted configuration; do not transfer values to another model.
Compare alternative quotations only after each supplier identifies the complete model, configuration and matching documents. No universal suffix meaning or unsupported advantage over another model is asserted.
Purchasing review and enquiry preparation
Start with Pneumatic Sheep Carcass Rail Unloading Device | HT-S209 and its specification/source notes. Download the linked reference summary, then request the original configuration-specific drawing and current technical documents. The summary is not an approved drawing, certificate or acceptance record.
Use the linked sheep & goat processing application and purchasing guidance to review process interfaces, selection conditions and the proposed supply boundary. Verify which manufacturer, supplier and installation responsibilities are included; a reference photo does not establish factory ownership, certification or a completed HUATAO installation.
Before enquiry, prepare animal species or incoming product, size/weight range, target throughput, operating shifts, destination, available utilities and a layout or interface drawing. Quote HT-S209 and identify the missing documents or conditions you need checked. Use the enquiry on this page so the product and original source page are retained.
| PARAMETER | REFERENCE SPECIFICATION |
|---|---|
| Reference model | HT-S209 |
| Primary duty | Unload carcass from rail to scalding tank |
| Working distance | 170 mm |
| Overall dimensions | 415 × 500 × 1,200 mm |
| Maximum stated lifting weight | 300 kg |
| Actuation | Pneumatic |
| Cylinder material | Aluminium |
| Main frame and guide | Galvanized steel or stainless steel |
| Controls | Pneumatic controls included in the reference description |
| Air pressure / cycle rate | Not stated; confirm for final selection |
Buyer FAQ
Does 300 kg refer to hourly capacity?
No. It is the stated maximum lifting weight. Throughput depends on cylinder speed, controls and the receiving process.
What air pressure is required?
The source does not state it. The supplier must size the cylinder and confirm pressure, flow and air-quality requirHTnts.
Will it fit any rail trolley?
Not automatically. Send the trolley, hook and rail drawings so the guide and release geometry can be checked.
Can the device drop a carcass directly into a tank?
Only when the tank, drop height, splash protection and operator guarding have been designed for that transfer.
What safety devices should be included?
Typical provisions include a rail stop, guarded drop zone, home/extended sensors, HTrgency stop, lockable air isolation and an interlock with the receiver.
What information is needed to select this equipment?
Provide rail or belt dimensions, working height, travel direction, carrier spacing, load range, speed and upstream/downstream connection drawings. A similar-looking carrier is not proof of fit.
Are these specifications an approved supply commitment?
No. These are source reference details. The quotation must identify the exact configuration, drawing revision, included documents and agreed acceptance criteria.
Related configurations and guidance
Reference specification and document status
Download HT-S209 reference specification and verification checklist
This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.