SlaughterPro | HUATAOSearch

Sheep & Goat Living Halal Killing Box | HT-S101-II

Sheep & Goat Living Halal Killing Box. Compare animal range, handling method and transfer interfaces; share your requirements for configuration review.

HT-S101-II sheep and goat hydraulic restraint and rotating box — source family image; confirm the quoted configuration

Specification notes

ModelHT-S101-II
Listed capacity150–200 head/hour
Listed supply380 V, 3-phase, 50 Hz
Listed installed power3.0 + 2.2 kW
Listed rotation180°
Listed dimensions1400 × 1200 × 1600 mm
Data statusSource reference R1, 2026-11-16; configuration and performance require written confirmation
Listed weight≤1800 kg
Listed main materialCarbon steel or stainless steel; confirm configuration
Listed side platesPolyamide
DriveHydraulic

Use and process position

HT-S101-II is described in the supplied product document as a hydraulic restraint and rotating box for sheep and goats. The source places it after live-animal restraint and before bleeding transfer. It is intended for assessment in sheep and goat slaughter projects; suitability depends on animal dimensions, operating procedure and the receiving line.

Structure and operation

The source describes an entrance gate, hydraulic restraint, a rotating box and polyamide side plates. The restrained animal is positioned for the slaughter operation, then the box rotates for transfer towards the bleeding rail or conveyor. Confirm guarding, operator access, interlocks, emergency stopping and the transfer method in the proposed drawing before use.

Configuration choices and selection limits

The source lists carbon steel or stainless steel construction. Its feature text also mentions hot galvanizing, without defining a separate model. The quotation must therefore identify material grades, finishes and contact surfaces explicitly; these are configuration choices, not interchangeable confirmed specifications.

The listed 150–200 head/hour is reference throughput, dependent on animal range, operator workflow and adjacent equipment. No approved live-weight range, guaranteed cycle time or site-specific throughput is established by this source. Do not select the machine by capacity alone. The listed 380 V, three-phase, 50 Hz supply must be checked against the destination utilities; alternative supplies are not confirmed.

Evidence and document verification

Source reference: supplied Word document “1. 羊致昏 屠宰 放血设备.doc”, section 1.13, technical specification table; local extraction lines 2509–2629. Reference compilation R1 dated 2026-11-16. This is a source record, not a manufacturer approval revision.

No model-specific approved drawing, inspection record or certificate is linked in the current page evidence set. The product name uses “Halal” as a source description of intended workflow; it does not establish Halal certification or regulatory approval. Ask for document issuer, scope, model coverage and current revision before relying on any certificate. Source case narratives are not presented as verified HUATAO installations.

Before quotation and acceptance

Provide animal species, live weight and size range, required throughput, shifts, destination country, available electrical supply, floor space and upstream/downstream interface drawings. Request a configuration-specific drawing, material schedule, safety arrangement, utility list, delivery scope and agreed inspection or acceptance criteria. These items establish what will be supplied and checked; their availability must be confirmed in the quotation.

Installation and process interfaces

Provide the full animal weight/size range, approach and exit route, operator position and the interface to the receiving rail or conveyor. Allow access for the proposed guarding and maintenance arrangement.

Utilities, control and feedback requirements

Confirm the proposed electrical, pneumatic or hydraulic arrangement from the matching model table. Agree control positions, emergency stopping and interlocks with the responsible engineering team; do not assume a universal slaughter procedure or approval.

Maintenance and part identification

Request the configuration-specific manual and part references for restraint components, drive parts, hoses and controls where fitted. Agree quantities and replenishment needs against actual duty and delivery experience. This page does not prescribe maintenance intervals, repairs or a guaranteed stock position.

Configuration-specific document checklist

Before purchase, identify the complete model and suffix, configuration table and drawing revision. Request the applicable layout/interface drawing, specification, manual, parts list and agreed inspection or test records. Performance curves or certificates should be linked only when an applicable original exists; a reference summary is not a substitute.

Model comparison: what the suffix does not prove

The supplied source identifies HT-S101-I as a pneumatic sheep stunning box, with source-listed capacity up to 150 head/hour, working pressure 0.6–0.8 MPa and approximate air consumption 190 L/time. HT-S101-II is described as a hydraulic restraint and rotating box, with listed capacity 150–200 head/hour and 380 V, three-phase, 50 Hz supply. These are distinct source configurations and process roles, not a universal upgrade sequence. Compare animal range, operating procedure, utilities, layout and receiving-line interfaces against the matching source table. Neither listed rate is an unconditional project guarantee; suffixes do not establish interchangeability.

Your purchasing review: evidence, application and next step

1. Check the HT-S101-II reference table and download the reference specification below. Record the listed voltage, dimensions and source status; the reference does not replace an approved drawing.

2. Open the restraint, slaughter and bleeding planning guide and the sheep/goat workflow application linked below. Check animal movement, operator access and transfer to the receiving rail against your existing line.

3. Read the complete-model and suffix guide before comparing quotations. Use the supplier-evaluation guide to request configuration-specific drawings, material details and inspection evidence. HUATAO is an independent supplier working with manufacturers; this page does not demonstrate HUATAO factory ownership, certification or verified installations.

4. Prepare the animal size/weight range, target throughput, destination, electrical supply and interface layout. Use the project planner or equipment enquiry link below, specifying HT-S101-II. The enquiry carries the product and source page so the supply scope and missing documents can be reviewed before a quotation.

Source reference configuration 1
ItemSpecification
Product NameSheep & Goat Living Halal Killing Box
ModelHT-S101-II
ApplicationSheep & Goat Halal Slaughter
Working PrincipleHydraulic
Rated Voltage380V
Frequency50Hz
Phase3 Phase
Installed Power3.0 + 2.2 kW
Hydraulic Rotation180°
Capacity150–200 Heads/hour
Machine Size1400 × 1200 × 1600 mm
Weight≤1800 kg
Main MaterialCarbon Steel or Stainless Steel
Side PlatePolyamide Plate

Buyer FAQ

Does the product name prove Halal certification?

No. It describes the workflow in the supplied source. Certification, animal welfare procedure and destination requirements must be verified separately for the actual project.

Is 150–200 head/hour guaranteed for every project?

No. It is a source-listed reference. Confirm animal range, operator workflow, transfer interfaces and acceptance conditions in writing.

Can it connect to an existing bleeding rail?

The source describes integration with bleeding equipment. Provide rail height, layout, transfer direction and connection dimensions for engineering confirmation.

Related configurations and guidance

Check complete models and suffix differences Review sheep and goat process interfaces Organise project conditions for technical review Sheep & goat processing equipment categories Check complete model identifiers and suffixes Compare the HT-S101-I pneumatic box source configuration

Reference specification and document status

Download HT-S101-II reference specification and verification checklist

This reference is not an approved manufacturing drawing, inspection report or certificate. Request the configuration-specific documents before purchase.

Applications

Sheep & goat processing workflowExplore sheep & goat processing by process task, source equipment and project conditions.

Capabilities

Sheep & goat processing line planningExplore sheep & goat processing by process task, source equipment and project conditions.

Technical resources

Download RFQ preparation checklistsProject, machine and replacement part information to prepare before an enquiry.

Selection guides

Check the complete model and suffix before buyingA prefix finds a family; the complete model, configuration and drawing establish the enquiry.

Request specifications

Add company or technical details (optional)

Equipment under review: HT-S101-II

Start with what you know. You can send drawings or photographs by email.

Continue your technical review